# Fiche technique : tableaux de données, en-têtes fusionnés

> Des tableaux collés en TSV, lus par parseTSV, façonnés par mergeCells, setAlignment et setCellBackground ; une carte de registres qui se coupe seule.

- Version HTML: https://postext.dev/fr/cookbook/technical-datasheet
- Recette Nº 010 · Tableaux · Niveau 3 (Avancé) · Sorties: Canvas, PDF
- Genres: Manuels, guides et ouvrages de référence
- Nécessite postext ≥ 1.28.0, postext-pdf ≥ 1.28.0 · testée avec 1.31.0, postext-pdf 1.31.0 le 2026-10-13
- Pages: [1](https://postext.dev/cookbook/technical-datasheet/en/p01.webp?v=e4d84103), [2](https://postext.dev/cookbook/technical-datasheet/en/p02.webp?v=e4d84103), [3](https://postext.dev/cookbook/technical-datasheet/en/p03.webp?v=e4d84103), [4](https://postext.dev/cookbook/technical-datasheet/en/p04.webp?v=e4d84103)
- PDF: https://postext.dev/cookbook/technical-datasheet/en/technical-datasheet.pdf?v=e4d84103
- Ouvrir dans le Sandbox: https://postext.dev/fr/sandbox#recipe=technical-datasheet&lang=en (.postext: https://postext.dev/cookbook/technical-datasheet/en/technical-datasheet.postext)
- Dernière mise à jour: 2026-10-11
- Autres langues: [en](https://postext.dev/en/cookbook/technical-datasheet.md), [es](https://postext.dev/es/cookbook/technical-datasheet.md), [ca](https://postext.dev/ca/cookbook/technical-datasheet.md), [pt](https://postext.dev/pt/cookbook/technical-datasheet.md), [zh](https://postext.dev/zh/cookbook/technical-datasheet.md), [ja](https://postext.dev/ja/cookbook/technical-datasheet.md), [ar](https://postext.dev/ar/cookbook/technical-datasheet.md)

## En bref

Une fiche produit de quatre pages pour un capteur de température électronique. Elle montre comment construire des tableaux à partir de données de tableur, avec des en-têtes communs et un long tableau qui continue page suivante.

## Ce que vous allez composer

Voici la fiche technique de quatre pages du PX-7021, un capteur de température d’un fabricant imaginaire, Pyxis Microdevices. Elle est faite surtout de tableaux, avec des en-têtes pleins de cellules fusionnées et une carte de registres plus longue qu’une colonne. La première page s’ouvre sur une bande violette avec la référence du composant et trois chiffres clés. En page 2, un tableau occupe toute la largeur de la page. Son en-tête sur deux rangs place Value au-dessus de Min, Typ et Max ; les groupes de paramètres sont fusionnés dans la première colonne, et un paramètre sur deux est teinté de gris. La carte de registres se coupe au pied de la page 3 et continue en page 4 avec son en-tête répété, à côté des références de commande et au-dessus du dessin du boîtier. Les tableaux sont des données de tableur collées en TSV, car Postext ne lit pas les tableaux Markdown.

**Cette recette répond à:**

- Comment faire de données collées un tableau à en-têtes fusionnés, avec largeurs et alignement par cellule ?
- Comment couper un long tableau sur plusieurs pages avec un en-tête répété et une mention « suite » ?
- Comment styler plusieurs tableaux différemment (fonds, cellules zébrées, cadres arrondis) dans un même document ?
- Comment garder des schémas nets, avec du texte sélectionnable, dans le PDF (SVG, originaux pour l’impression) ?
- Comment ajouter des images et des tableaux depuis le code (ressources) plutôt qu’avec ![]() en Markdown ?

## La réponse courte

```js
// script.js, lignes 31–69
const at = (row, column) => ({ row, col: column });
const span = (r0, c0, r1, c1) => ({ start: at(r0, c0), end: at(r1, c1) });
const C = { group: 0, param: 1, symbol: 2, conditions: 3, min: 4, max: 6, unit: 7 }; // columns
function electricalTable(tsv) {
  // headerRows marks the head, two rows here, which a split table would repeat on each part.
  let m = Object.assign(parseTSV(tsv, { headerRows: 2 }), {
    columnWidths: [22, 44, 16, 38, 15, 15, 15, 15] }); // weights: mm of the 180 mm measure
  // 'Parameter' covers two columns and two rows; 'Value' spans Min, Typ and Max. mergeCells
  // marks the covered cells hiddenBy, so no column shifts (gotcha: merged-cells-hiddenby).
  for (const range of [span(0, C.group, 1, C.param), span(0, C.symbol, 1, C.symbol),
    span(0, C.conditions, 1, C.conditions), span(0, C.min, 0, C.max),
    span(0, C.unit, 1, C.unit)]) {
    m = mergeCells(m, range); // 'Value' is centred over its three columns, the rest set left
    m = setAlignment(m, range.start, range.start.col === C.min ? 'center' : 'left', 'middle');
  }
  // Min, Typ and Max go right, over their figures; setAlignment clears a vAlign it is not given.
  for (let c = C.min; c <= C.max; c++) m = setAlignment(m, at(1, c), 'right');
  let zebra = false;
  for (let r = m.headerRowCount; r < m.rows.length; r++) {
    const row = m.rows[r];
    if (row[C.param].content) zebra = !zebra; // a parameter keeps one fill over its conditions
    for (let c = 0; c < row.length; c++) {
      // An empty cell continues the one above: a group, or a parameter and its symbol.
      if (c <= C.symbol && row[c].content) {
        let end = r;
        while (m.rows[end + 1] && !m.rows[end + 1][c].content
          && (c === C.group || !m.rows[end + 1][C.param].content)) end++;
        m = mergeCells(m, span(r, c, end, c));
      }
      // Figures flush right, as datasheets set them (no decimal tab: gap tab-stops).
      m = setAlignment(m, at(r, c), c >= C.min && c <= C.max ? 'right' : 'left', 'middle');
      // tableStyle.bodyAlternateBackground alternates row by row; this fill changes with the
      // parameter, so it is set cell by cell. Each helper returns a new model, cheap at 20 rows.
      if (c === C.group) m = setCellBackground(m, at(r, c), col('tint'));
      else if (zebra) m = setCellBackground(m, at(r, c), col('zebra'));
    }
  }
  return m;
}
```

## Ingrédients

**Enseigne**

- [Tableaux à partir de données](https://postext.dev/fr/docs/document-format.md#insertion-en-bloc-facultative-placement-explicite-dans-le-texte): Des ressources tableau avec des lignes d’en-tête, des cellules fusionnées, des proportions de colonnes, un alignement par cellule et des listes dans les cellules ; les tableaux à barres verticales ne sont pas analysés.
- [Tableaux sur plusieurs pages](https://postext.dev/fr/docs/configuration-resources.md#tableaux-plus-hauts-que-la-page): Les tableaux longs se coupent entre les lignes avec l’en-tête répété, « (suite) » dans la légende et une mention « À suivre », jamais à l’intérieur d’un rowspan.

**Utilise aussi**

- [Fonds de cellule](https://postext.dev/fr/docs/document-format.md#insertion-en-bloc-facultative-placement-explicite-dans-le-texte)
- [Styles de tableau nommés](https://postext.dev/fr/docs/configuration-resources.md#styles-de-tableau-nommés)
- [Style de tableau](https://postext.dev/fr/docs/configuration-resources.md#style-de-tableau)
- [Style des légendes](https://postext.dev/fr/docs/configuration-resources.md#style-de-légende)
- [Attributs de titre](https://postext.dev/fr/docs/document-format.md#attributs-de-titre)
- [Exposants et indices](https://postext.dev/fr/docs/document-format.md#mise-en-forme-en-ligne)
- [Pastilles dans le texte](https://postext.dev/fr/docs/configuration-styles.md#styles-de-pastille)
- [Figures et tableaux comme ressources](https://postext.dev/fr/docs/document-format.md#ressources)
- [Placement des figures](https://postext.dev/fr/docs/document-format.md#placement)
- [Ouvertures composées](https://postext.dev/fr/docs/configuration-text.md#étendue-et-maquette-avancée)
- [Bandeau de chapitre sur toute la largeur](https://postext.dev/fr/docs/configuration-text.md#étendue-et-maquette-avancée)
- [Images dans les maquettes de page](https://postext.dev/fr/docs/configuration-page-layout.md#éléments-image)
- [Titres courants et folios](https://postext.dev/fr/docs/configuration-page-layout.md#en-têtes-et-pieds-de-page)
- [Titres numérotés](https://postext.dev/fr/docs/configuration-text.md#réglages-par-niveau)
- [Encadrés](https://postext.dev/fr/docs/configuration-styles.md#styles-dencadré)
- [Palette de couleurs sémantique](https://postext.dev/fr/docs/configuration-fonts-colors-viewers.md#palette-de-couleurs)
- [Export PDF](https://postext.dev/fr/docs/configuration-programmatic-usage.md#générer-des-pdf)
- [Des citations qui placent les figures](https://postext.dev/fr/docs/document-format.md#renvoi-dans-le-texte-la-forme-principale)
- [Styles de titre](https://postext.dev/fr/docs/configuration-styles.md#styles-de-titre)
- [Figure et Tableau dans votre langue](https://postext.dev/fr/docs/configuration-resources.md#types-de-ressources)
- [Sauts de page et de colonne](https://postext.dev/fr/docs/document-format.md#pagebreak)
- [Titres courants selon le rôle de la page](https://postext.dev/fr/docs/configuration-page-layout.md#éléments-de-texte)
- [Styles de paragraphe](https://postext.dev/fr/docs/configuration-styles.md#styles-de-paragraphe)
- [Polices intégrées au PDF](https://postext.dev/fr/docs/configuration-programmatic-usage.md#pourquoi-un-fournisseur-de-polices)
- [Types de ressource personnalisés](https://postext.dev/fr/docs/configuration-resources.md#types-de-ressources)

**La configuration en un coup d’œil**

- [`bodyText`](https://postext.dev/fr/docs/configuration-text.md#texte-courant), [`calloutStyles`](https://postext.dev/fr/docs/configuration-styles.md#styles-dencadré), [`captionStyle`](https://postext.dev/fr/docs/configuration-resources.md#style-de-légende), [`chipStyles`](https://postext.dev/fr/docs/configuration-styles.md#styles-de-pastille), [`colorPalette`](https://postext.dev/fr/docs/configuration-fonts-colors-viewers.md#palette-de-couleurs), [`footer`](https://postext.dev/fr/docs/configuration-page-layout.md#en-têtes-et-pieds-de-page), [`header`](https://postext.dev/fr/docs/configuration-page-layout.md#en-têtes-et-pieds-de-page), [`headingStyles`](https://postext.dev/fr/docs/configuration-styles.md#styles-de-titre), [`headings`](https://postext.dev/fr/docs/configuration-text.md#titres), [`layout`](https://postext.dev/fr/docs/configuration-page-layout.md#mise-en-page), [`locale`](https://postext.dev/fr/docs/configuration-text.md#césure), [`page`](https://postext.dev/fr/docs/configuration-page-layout.md#page), [`paragraphStyles`](https://postext.dev/fr/docs/configuration-styles.md#styles-de-paragraphe), [`resourceTypes`](https://postext.dev/fr/docs/configuration-resources.md#types-de-ressources), [`tableStyle`](https://postext.dev/fr/docs/configuration-resources.md#style-de-tableau), [`tableStyles`](https://postext.dev/fr/docs/configuration-resources.md#styles-de-tableau-nommés), [`unorderedLists`](https://postext.dev/fr/docs/configuration-text.md#listes-à-puces)

**API**

- [`buildDocumentWithFonts`](https://postext.dev/fr/docs/configuration-programmatic-usage.md#charger-les-polices-avant-la-mise-en-page), [`decompressWoff2`](https://postext.dev/fr/docs/configuration-programmatic-usage.md#fournisseur-de-polices-dans-le-navigateur-fontsource--woff2), [`defaultResourceTypes`](https://postext.dev/fr/docs/configuration-resources.md#types-de-ressources), [`inlineSvgFonts`](https://postext.dev/fr/docs/configuration-resources.md#polices-du-texte-svg), [`mergeCells`](https://postext.dev/fr/docs/document-format.md#insertion-en-bloc-facultative-placement-explicite-dans-le-texte), [`parseTSV`](https://postext.dev/fr/docs/document-format.md#insertion-en-bloc-facultative-placement-explicite-dans-le-texte), [`prepareFonts`](https://postext.dev/fr/docs/configuration-programmatic-usage.md#charger-les-polices-avant-la-mise-en-page), [`registerResourceImage`](https://postext.dev/fr/docs/architecture.md#surface-de-lapi), [`renderPageToCanvas`](https://postext.dev/fr/docs/configuration-programmatic-usage.md#rendre-une-page-en-bitmap), [`renderToPdf`](https://postext.dev/fr/docs/configuration-programmatic-usage.md#générer-des-pdf), [`setAlignment`](https://postext.dev/fr/docs/document-format.md#insertion-en-bloc-facultative-placement-explicite-dans-le-texte), [`setCellBackground`](https://postext.dev/fr/docs/document-format.md#insertion-en-bloc-facultative-placement-explicite-dans-le-texte)

**Caractères**

- Fira Sans (OFL-1.1), Fira Sans Condensed (OFL-1.1), Fira Mono (OFL-1.1)

## Préparation

### 1 · Coller les données, puis façonner le tableau

Le code est dans [la réponse courte](https://postext.dev/fr/cookbook/technical-datasheet.md#la-réponse-courte) plus haut. `parseTSV(tsv, { headerRows: 2 })` marque les deux rangs d’en-tête ; si le tableau se coupait, les deux se répéteraient sur chaque partie. Les poids de `columnWidths` totalisent 180, la largeur du bloc de texte en millimètres : chaque poids est donc la largeur de sa colonne sur la page. `mergeCells` garde chaque cellule couverte à sa place et la marque `hiddenBy` : aucune colonne ne se décale. `setAlignment` agit cellule par cellule et efface l’alignement vertical quand vous l’omettez : la plupart des appels repassent donc `'middle'`. Le gris alterne d’un paramètre au suivant, ce qui garde les deux rangs d’Accuracy sur le même fond ; alterner par rang, comme le fait le `bodyAlternateBackground` du style de tableau, laisserait le second en blanc.

### 2 · Chaque modèle devient une ressource

```js
// script.js, lignes 492–521
const svgResource = (id, caption, altText, [w, h], placement) => ({ id, typeId: 'figure',
  kind: 'svg', caption, altText, placement, createdAt: 0, updatedAt: 0,
  svg: { fileId: `${id}.svg`, width: w * SCALE, height: h * SCALE } }); // fitted to its slot
const table = (id, caption, model, { styleId, placement, note } = {}) => ({ id, typeId: 'table',
  kind: 'table', caption, note, placement, table: { model, styleId }, createdAt: 0, updatedAt: 0 });
// A float takes the first free slot after its first :ref; the logo is never cited, only drawn.
const resources = [
  svgResource('logo', '', 'Pyxis Microdevices', LOGO),
  svgResource('pinout', 'Pin configuration, 8-pin DFN, top view.', 'The package from above: '
    + 'pins 1 to 4 down the left side, 5 to 8 up the right.', PINOUT),
  svgResource('circuit', 'Typical application, bus address 48h.', 'The sensor with a 100 nF '
    + 'capacitor, address pins to ground, and SDA, SCL and ALERT pulled up to a host.', CIRCUIT),
  svgResource('outline', 'Package outline and land pattern, 8-pin DFN, in mm.', 'Top, bottom '
    + 'and side views of the 2 × 2 mm body, and the land pattern with its two vias.', OUTLINE,
  { position: 'bottom', span: 'page' }), // a strip across the foot of a page
  table('electrical', 'Electrical characteristics, *V*~DD~ = 1.6 V to 5.5 V and *T*~A~ = −40 °C '
    + 'to 125 °C unless noted', electricalTable(electrical), { styleId: 'electrical',
    placement: { position: 'top', span: 'page' }, note: 'Typical values at 3.3 V and 25 °C. '
      + '^1^ Tested at 25 °C and 50 °C, the rest by characterization. ^2^ Characterized, not '
      + 'tested in production. ^3^ One conversion a second, bus idle.' }),
  // No placement: these float to the first free slot after their reference and split there.
  table('pins', 'Pin functions', groupedTable(pins, [9, 16, 10, 52]), { styleId: 'grouped',
    note: 'Types: P power, G ground, I input, O open-drain output, I/O open-drain input and '
      + 'output.' }),
  table('registers', 'Register map', groupedTable(registers, [9, 17, 11, 50]), {
    styleId: 'grouped', note: 'Reset values apply at power-on and after a general-call reset.' }),
  table('ordering', 'Order codes', Object.assign(parseTSV(ordering, { headerRows: 1 }), {
    columnWidths: [23, 29, 18, 17] }), { styleId: 'ordering',
    note: 'WLCSP-4: fixed address 48h, no ALERT output.' }),
];
```

Chaque tableau et chaque dessin est une ressource avec une légende, et les tableaux ajoutent une note et un style nommé. Légendes et notes acceptent l’italique, les indices et les exposants : le tableau électrique donne ses conditions de test avec `*V*~DD~` dans la légende et numérote ses notes avec `^1^` dans la note. Un flottant prend le premier emplacement libre après son premier `:ref`. Le tableau 1 est cité en page 1 et placé en tête de page sur toute la largeur : il ouvre donc la page 2. Le dessin du boîtier est placé au pied d’une page sur toute la largeur, et les autres tableaux gardent le placement par défaut, un flottant large d’une colonne. Un tableau placé `here` reste dans le texte ; quand il ne tient pas dans le reste de sa colonne, il se coupe lui aussi entre deux rangs.

### 3 · Laisser un long tableau se couper seul

```js
// script.js, lignes 73–87
function groupedTable(tsv, columnWidths) {
  let m = Object.assign(parseTSV(tsv, { headerRows: 1 }), { columnWidths });
  const codes = [0, 2]; // Pin and Type, Addr. and Reset: short codes, centred, in a bare chip
  // A TSV cell holds no line break: the data writes \n, and a line opening with • is a list.
  m.rows = m.rows.map((row, r) => row.map((cell, c) => ({ ...cell,
    content: r > 0 && row[1].content && codes.includes(c) ? `:chip[${cell.content}]{style="code"}`
      : cell.content.replaceAll('\\n', '\n') })));
  for (let r = 0; r < m.rows.length; r++) {
    const last = m.rows[r].length - 1;
    if (r >= m.headerRowCount && !m.rows[r][1].content) { // a lone first cell heads a group
      m = setCellBackground(mergeCells(m, span(r, 0, r, last)), at(r, 0), col('tint'));
    } else for (const c of codes) m = setAlignment(m, at(r, c), 'center');
  }
  return m; // no split code: the engine cuts it between rows and repeats the head
}
```

Le tableau des broches et la carte de registres sortent tous deux de `groupedTable`. Un rang dont seule la première cellule est remplie est fusionné sur toute la largeur du tableau et teinté de violet comme tête de groupe. Une cellule TSV ne peut pas contenir de saut de ligne : les données écrivent donc `\n` et la fonction le transforme en saut de ligne ; une ligne qui commence par `•` est alors composée comme un élément de liste. Les codes courts prennent le style de pastille `code`, sans fond, sans bordure ni marge latérale, qui les compose en Fira Mono à 0,9 em. Quand un tableau flottant ne tient pas dans la colonne vide qu’on lui propose, le moteur le coupe entre deux rangs et compose la suite dans l’emplacement libre suivant, sous l’en-tête répété, avec `(continued)` après la légende. La ligne `continuesMarker`, « Continued on the next page », se place sous la première partie, et la note attend la dernière ([tableaux plus hauts que la page](https://postext.dev/fr/docs/configuration-resources.md#tableaux-plus-hauts-que-la-page)).

### 4 · Un style maison, une variante par tableau

```js
// script.js, lignes 191–205
  tableStyle: { headerBackground: col('brand'), headerColor: col('paper'), headerFontFamily: COND,
    headerFontSize: pt(8.5), bodyFontSize: pt(8), rules: 'horizontal', borderColor: col('rule'),
    borderWidth: pt(0.5), cellPadding: mm(1.3) },
  tableStyles: [ // a resource picks one with table.styleId
    // White rules cut the fills apart and show where each merge and each group ends.
    { id: 'electrical', borderColor: col('paper'), borderWidth: pt(1.4), cellPadding: mm(1.1) },
    // Written out although it is the default: 'clip' and 'hide' cut a table taller than the page.
    { id: 'grouped', overflow: 'split', continuedSuffix: '(continued)',
      continuesMarker: 'Continued on the next page' },
    // A compact list in the condensed face, boxed by a rounded outer frame.
    { id: 'ordering', headerBackground: col('tint'), headerColor: col('brand'),
      rules: 'outer', borderRadius: mm(1.5), bodyFontFamily: COND },
  ],
  captionStyle: { fontFamily: COND, fontSize: pt(9.5), labelColor: col('brand'), gap: mm(2),
    note: { fontSize: pt(7.5), color: col('muted') } },
```

`tableStyle` contient ce que partagent tous les tableaux. Chaque entrée de `tableStyles` ne règle que ce que ses tableaux changent, et une ressource en choisit une avec `table.styleId`. Le tableau électrique remplace les filets fins gris par des filets blancs de 1,4 pt, qui séparent ses fonds et montrent où finit chaque fusion. Le tableau des références de commande reçoit un cadre extérieur arrondi et Fira Sans Condensed, pour que ses quatre colonnes tiennent dans une colonne de texte.

### 5 · Des étiquettes qui restent du texte dans le PDF

```js
// script.js, lignes 535–540
// label() writes each <text> with font-family="Fira Mono". loadSvg runs the markup through
// inlineSvgFonts, which embeds that face in the SVG, so the canvas draws the labels in it;
// the PDF sets them as real text in the Fira Mono it embeds.
await loadSvg('logo.svg', logo);
const drawings = { pinout: pinout(), circuit: circuit(), outline: outline() }; // by resource id
for (const [id, markup] of Object.entries(drawings)) await loadSvg(`${id}.svg`, markup);
```

Les étiquettes du brochage, du schéma et du dessin du boîtier sont des éléments `<text>` qui demandent Fira Mono, le caractère des étiquettes du document. Un SVG arrive sur le canvas comme une image : le `loadSvg` du kit fait donc d’abord passer le balisage par `inlineSvgFonts`, qui incorpore dans le SVG les caractères que nomme son texte ; le canvas dessine alors les étiquettes en Fira Mono. Le PDF compose chaque `<text>` comme du texte sélectionnable dans les caractères qu’il incorpore.

### 6 · Ouverture, titre courant et pied de page

```js
// script.js, lignes 96–146
const place = (to, edge, x, y, size) => ({ anchor: { to, edge }, offset: { x: mm(x), y: mm(y) },
  ...(size && { size }) });
const inset = (edge, y, size) => // a page corner, moved in by the side margin
  place('page', edge, edge.endsWith('left') ? MARGIN.x : -MARGIN.x, y, size);
const text = (id, content, family, size, color, placement, extra) => ({ kind: 'text', id,
  content, fontFamily: family, fontSize: pt(size), color: col(color), placement, ...extra });
const caps = (size, weight = 600) => ({ fontWeight: weight, letterSpacing: pt(size * 0.16),
  textTransform: 'uppercase' });
const badge = { ...caps(7.5, 700), box: { backgroundColor: col('hazard'),
  padding: { top: pt(1.6), bottom: pt(1.4), left: pt(4), right: pt(4) } } };
const mark = (size, edge, y) => ({ kind: 'image', id: 'mark', resourceId: 'logo', // by id
  placement: inset(edge, y, { width: mm(size) }) });
const maker = (size, color, y) => text('maker', 'Pyxis Microdevices', COND, size, color,
  place('#mark', 'right-of', size / 4, y), caps(size));
const keyFigure = (n, y) => [ // {attr.k1} over its label {attr.k1l}, flush right on the band
  text(`k${n}`, `{attr.k${n}}`, COND, 22, 'paper', inset('top-right', y), { fontWeight: 600 }),
  text(`k${n}l`, `{attr.k${n}l}`, COND, 7, 'tint', inset('top-right', y + 9), caps(7))];
const BAND = 84; // mm: the violet band across the head of page 1
// The band under the top margin and 9 mm or more of white, in whole grid lines (16 here).
const OPENER_LINES = Math.ceil((BAND - MARGIN.y + 9) / (LEAD * 25.4 / 72));
const opener = {
  enabled: true, minHeight: pt(OPENER_LINES * LEAD), // so the columns under it start on the grid
  slot: { elements: [
    { kind: 'box', id: 'band', style: { backgroundColor: col('brand') }, placement: {
      anchor: { to: 'bleed', edge: 'top-left' }, size: { width: 'fill', height: mm(BAND) } } },
    mark(6, 'top-left', 12), maker(8.5, 'paper', 1.7),
    text('doc', 'Datasheet {subtitle} · {publishDate}', MONO, 7.5, 'tint',
      inset('top-right', 13.6)),
    text('kicker', '{attr.kicker}', COND, 9.5, 'tint', inset('top-left', 30), caps(9.5)),
    text('title', '{titleText}', COND, 64, 'paper', place('#kicker', 'below', 0, 0.5),
      { fontWeight: 700, lineHeight: 1 }),
    text('lead', '{attr.lead}', 'Fira Sans', 12, 'paper', place('#title', 'below', 0, 2.5,
      { width: mm(108) }), { lineHeight: 1.32, align: 'left' }), // wraps within its width
    text('status', 'Preliminary', COND, 7.5, 'ink', place('#lead', 'below', 0, 4.5), badge),
    ...[1, 2, 3].flatMap((n) => keyFigure(n, 15 + 15 * n)),
  ] },
};
const header = { elements: [ // body pages only: the opener has its band
  text('running-title', '{chapterTitle}', COND, 9, 'brand', inset('top-left', 10.4),
    { fontWeight: 700, pages: 'body' }),
  text('flag', 'Preliminary', COND, 7.5, 'ink', inset('top-right', 10.2),
    { ...badge, pages: 'body' }),
  { kind: 'rule', id: 'hairline', pages: 'body', thickness: pt(0.5), color: col('rule'),
    placement: inset('top-left', 15.5, { width: mm(TRIM[0] - 2 * MARGIN.x) }) },
] };
const footer = { elements: [ // every page: an image element works in a running slot too
  mark(4.5, 'bottom-left', -9), maker(7, 'ink', 1.2),
  text('folio', '{pageNumber}/{totalPages}', COND, 8, 'brand', inset('bottom-right', -9.6),
    { fontWeight: 700 }),
  text('doc', '{subtitle} ·', MONO, 7, 'muted', place('#folio', 'left-of', -1.5, 0.4)),
] };
```

La référence du composant est le titre de niveau 1, et son emplacement de maquette dessine l’ouverture : une boîte violette jusqu’au fond perdu, le logo, ainsi qu’un surtitre, un chapeau et trois chiffres clés lus dans les attributs du titre. Les éléments image fonctionnent dans les emplacements courants comme dans les ouvertures : le pied de page commence donc par l’un d’eux, qui nomme la ressource du logo. Les éléments du titre courant portent `pages: 'body'` : aucun ne s’imprime sur la première page.

## La recette complète

Un seul fichier, composé à partir du dossier de la recette avec le texte d’exemple et le kit commun des Recettes déjà inclus ; il construit sa propre page. Pour l’exécuter, placez-le dans un `<script type="module">` d’une page vide ou collez-le dans le panneau JS d’un nouveau pen CodePen (en tant que module). Il importe postext depuis esm.sh : il n’y a rien à installer ni à compiler.

- Dossier de la recette: https://github.com/drnachio/postext/tree/main/cookbook/technical-datasheet

### script.js

```js
// ═══ Postext Cookbook · Nº 010 · Datasheet: tables from data, merged headers ════════
// https://postext.dev/en/cookbook/technical-datasheet
// Code: MIT · Text: original (CC BY 4.0) · Drawings: generated in code (CC BY 4.0)
// Fonts: Fira Sans, Fira Sans Condensed, Fira Mono (SIL OFL 1.1) · Needs postext ≥ 1.28.0
// The datasheet of a fictional sensor. Postext reads no pipe tables, so the tables are data:
// TSV pasted from a spreadsheet, parsed into table models, then merged, aligned and filled.
import {
  buildDocumentWithFonts, prepareFonts, renderPageToCanvas, registerResourceImage,
  defaultResourceTypes, parseTSV, mergeCells, setAlignment, setCellBackground, inlineSvgFonts,
} from 'https://esm.sh/postext';
import { renderToPdf, decompressWoff2 } from 'https://esm.sh/postext-pdf';

const LANG = 'en'; // @lang: the language of the sample document ('en' | 'es')
const RECIPE = 'technical-datasheet';

// ─── 1 · Design ─────────────────────────────────────────────────────────────
const palette = { // eight named colours; every colour in the config links to one of them
  ink: '#16181d', brand: '#5a2a8a', // text; Pyxis violet: the band, table heads, numbers
  tint: '#eee6f5', zebra: '#f3f4f6', // violet wash for groups and pins; every other row
  hazard: '#f2b705', rule: '#c9ccd3', // maximum ratings and the badge; hairlines
  muted: '#5d636d', paper: '#ffffff', // running heads, notes and units; white
};
// Every colour carries its paletteId: change a value in `palette` and all its uses follow.
const col = (id) => ({ hex: palette[id], model: 'hex', paletteId: id });
const colorPalette = [ // the defaults link to 'main-color', so it is set to the brand violet
  ...Object.entries(palette).map(([id, hex]) => ({ id, name: id, value: { hex, model: 'hex' } })),
  { id: 'main-color', name: 'brand (defaults)', value: { hex: palette.brand, model: 'hex' } },
];

// #region answer: pasted TSV becomes a table: two header rows, merged cells, zebra fills
const at = (row, column) => ({ row, col: column });
const span = (r0, c0, r1, c1) => ({ start: at(r0, c0), end: at(r1, c1) });
const C = { group: 0, param: 1, symbol: 2, conditions: 3, min: 4, max: 6, unit: 7 }; // columns
function electricalTable(tsv) {
  // headerRows marks the head, two rows here, which a split table would repeat on each part.
  let m = Object.assign(parseTSV(tsv, { headerRows: 2 }), {
    columnWidths: [22, 44, 16, 38, 15, 15, 15, 15] }); // weights: mm of the 180 mm measure
  // 'Parameter' covers two columns and two rows; 'Value' spans Min, Typ and Max. mergeCells
  // marks the covered cells hiddenBy, so no column shifts (gotcha: merged-cells-hiddenby).
  for (const range of [span(0, C.group, 1, C.param), span(0, C.symbol, 1, C.symbol),
    span(0, C.conditions, 1, C.conditions), span(0, C.min, 0, C.max),
    span(0, C.unit, 1, C.unit)]) {
    m = mergeCells(m, range); // 'Value' is centred over its three columns, the rest set left
    m = setAlignment(m, range.start, range.start.col === C.min ? 'center' : 'left', 'middle');
  }
  // Min, Typ and Max go right, over their figures; setAlignment clears a vAlign it is not given.
  for (let c = C.min; c <= C.max; c++) m = setAlignment(m, at(1, c), 'right');
  let zebra = false;
  for (let r = m.headerRowCount; r < m.rows.length; r++) {
    const row = m.rows[r];
    if (row[C.param].content) zebra = !zebra; // a parameter keeps one fill over its conditions
    for (let c = 0; c < row.length; c++) {
      // An empty cell continues the one above: a group, or a parameter and its symbol.
      if (c <= C.symbol && row[c].content) {
        let end = r;
        while (m.rows[end + 1] && !m.rows[end + 1][c].content
          && (c === C.group || !m.rows[end + 1][C.param].content)) end++;
        m = mergeCells(m, span(r, c, end, c));
      }
      // Figures flush right, as datasheets set them (no decimal tab: gap tab-stops).
      m = setAlignment(m, at(r, c), c >= C.min && c <= C.max ? 'right' : 'left', 'middle');
      // tableStyle.bodyAlternateBackground alternates row by row; this fill changes with the
      // parameter, so it is set cell by cell. Each helper returns a new model, cheap at 20 rows.
      if (c === C.group) m = setCellBackground(m, at(r, c), col('tint'));
      else if (zebra) m = setCellBackground(m, at(r, c), col('zebra'));
    }
  }
  return m;
}
// #endregion

// #region split: group rows, codes and lists in cells; a table taller than its slot splits
function groupedTable(tsv, columnWidths) {
  let m = Object.assign(parseTSV(tsv, { headerRows: 1 }), { columnWidths });
  const codes = [0, 2]; // Pin and Type, Addr. and Reset: short codes, centred, in a bare chip
  // A TSV cell holds no line break: the data writes \n, and a line opening with • is a list.
  m.rows = m.rows.map((row, r) => row.map((cell, c) => ({ ...cell,
    content: r > 0 && row[1].content && codes.includes(c) ? `:chip[${cell.content}]{style="code"}`
      : cell.content.replaceAll('\\n', '\n') })));
  for (let r = 0; r < m.rows.length; r++) {
    const last = m.rows[r].length - 1;
    if (r >= m.headerRowCount && !m.rows[r][1].content) { // a lone first cell heads a group
      m = setCellBackground(mergeCells(m, span(r, 0, r, last)), at(r, 0), col('tint'));
    } else for (const c of codes) m = setAlignment(m, at(r, c), 'center');
  }
  return m; // no split code: the engine cuts it between rows and repeats the head
}
// #endregion

const TRIM = [216, 279]; // mm: US Letter
const MARGIN = { y: 20, x: 18 }; // mm: equal side margins, since a loose sheet has no spine
const LEAD = 13; // pt: the body leading, the baseline grid the headings and the opener keep to
const COND = 'Fira Sans Condensed', MONO = 'Fira Mono'; // the display and the label faces

// #region furniture: the opener band, a running head, and the logo in every footer
const place = (to, edge, x, y, size) => ({ anchor: { to, edge }, offset: { x: mm(x), y: mm(y) },
  ...(size && { size }) });
const inset = (edge, y, size) => // a page corner, moved in by the side margin
  place('page', edge, edge.endsWith('left') ? MARGIN.x : -MARGIN.x, y, size);
const text = (id, content, family, size, color, placement, extra) => ({ kind: 'text', id,
  content, fontFamily: family, fontSize: pt(size), color: col(color), placement, ...extra });
const caps = (size, weight = 600) => ({ fontWeight: weight, letterSpacing: pt(size * 0.16),
  textTransform: 'uppercase' });
const badge = { ...caps(7.5, 700), box: { backgroundColor: col('hazard'),
  padding: { top: pt(1.6), bottom: pt(1.4), left: pt(4), right: pt(4) } } };
const mark = (size, edge, y) => ({ kind: 'image', id: 'mark', resourceId: 'logo', // by id
  placement: inset(edge, y, { width: mm(size) }) });
const maker = (size, color, y) => text('maker', 'Pyxis Microdevices', COND, size, color,
  place('#mark', 'right-of', size / 4, y), caps(size));
const keyFigure = (n, y) => [ // {attr.k1} over its label {attr.k1l}, flush right on the band
  text(`k${n}`, `{attr.k${n}}`, COND, 22, 'paper', inset('top-right', y), { fontWeight: 600 }),
  text(`k${n}l`, `{attr.k${n}l}`, COND, 7, 'tint', inset('top-right', y + 9), caps(7))];
const BAND = 84; // mm: the violet band across the head of page 1
// The band under the top margin and 9 mm or more of white, in whole grid lines (16 here).
const OPENER_LINES = Math.ceil((BAND - MARGIN.y + 9) / (LEAD * 25.4 / 72));
const opener = {
  enabled: true, minHeight: pt(OPENER_LINES * LEAD), // so the columns under it start on the grid
  slot: { elements: [
    { kind: 'box', id: 'band', style: { backgroundColor: col('brand') }, placement: {
      anchor: { to: 'bleed', edge: 'top-left' }, size: { width: 'fill', height: mm(BAND) } } },
    mark(6, 'top-left', 12), maker(8.5, 'paper', 1.7),
    text('doc', 'Datasheet {subtitle} · {publishDate}', MONO, 7.5, 'tint',
      inset('top-right', 13.6)),
    text('kicker', '{attr.kicker}', COND, 9.5, 'tint', inset('top-left', 30), caps(9.5)),
    text('title', '{titleText}', COND, 64, 'paper', place('#kicker', 'below', 0, 0.5),
      { fontWeight: 700, lineHeight: 1 }),
    text('lead', '{attr.lead}', 'Fira Sans', 12, 'paper', place('#title', 'below', 0, 2.5,
      { width: mm(108) }), { lineHeight: 1.32, align: 'left' }), // wraps within its width
    text('status', 'Preliminary', COND, 7.5, 'ink', place('#lead', 'below', 0, 4.5), badge),
    ...[1, 2, 3].flatMap((n) => keyFigure(n, 15 + 15 * n)),
  ] },
};
const header = { elements: [ // body pages only: the opener has its band
  text('running-title', '{chapterTitle}', COND, 9, 'brand', inset('top-left', 10.4),
    { fontWeight: 700, pages: 'body' }),
  text('flag', 'Preliminary', COND, 7.5, 'ink', inset('top-right', 10.2),
    { ...badge, pages: 'body' }),
  { kind: 'rule', id: 'hairline', pages: 'body', thickness: pt(0.5), color: col('rule'),
    placement: inset('top-left', 15.5, { width: mm(TRIM[0] - 2 * MARGIN.x) }) },
] };
const footer = { elements: [ // every page: an image element works in a running slot too
  mark(4.5, 'bottom-left', -9), maker(7, 'ink', 1.2),
  text('folio', '{pageNumber}/{totalPages}', COND, 8, 'brand', inset('bottom-right', -9.6),
    { fontWeight: 700 }),
  text('doc', '{subtitle} ·', MONO, 7, 'muted', place('#folio', 'left-of', -1.5, 0.4)),
] };
// #endregion

const config = () => ({ locale: 'en-us', // the datasheet is written in English
  // Tables and figures count 1, 2, 3 through the document; table captions sit above.
  resourceTypes: defaultResourceTypes(LANG).map((type) => ({ ...type, numberingTemplate: '{n}',
    ...(type.id === 'table' && { captionStyle: { position: 'above' } }) })),
  colorPalette, layout: { layoutType: 'double', gutterWidth: mm(6) },
  page: { width: mm(TRIM[0]), height: mm(TRIM[1]), dpi: 150, margins: { top: mm(MARGIN.y),
    bottom: mm(MARGIN.y), left: mm(MARGIN.x), right: mm(MARGIN.x) } },
  bodyText: { // ragged-right sans with space between paragraphs, as reports are set
    fontFamily: 'Fira Sans', fontSize: pt(9.3), lineHeight: pt(LEAD), color: col('ink'),
    boldFontWeight: 600, boldColor: col('ink'), italicColor: col('ink'), textAlign: 'left',
    referenceColor: col('brand'), firstLineIndent: pt(0), paragraphSpacing: true,
    hyphenateAcrossColumns: 'withinPage' }, // no compound is divided over a page
  headings: { fontFamily: COND, color: col('ink'),
    levels: [ // 'any': a loose sheet has no rectos, so the H1 asks for no blank page
      { level: 1, span: 'page', breakBefore: { enabled: true, parity: 'any' },
        advancedDesign: opener, marginBottom: pt(0) }, // the opener's minHeight sets the gap
      // Margin and line add up to whole grid lines (three, then two), so the grid adds no air.
      { level: 2, fontSize: pt(13), lineHeight: pt(2 * LEAD), color: col('brand'),
        numberingTemplate: '{2}', marginTop: pt(LEAD), marginBottom: pt(0) },
      { level: 3, fontSize: pt(10), lineHeight: pt(LEAD), fontWeight: 600,
        numberingTemplate: '{2}.{3}', marginTop: pt(LEAD), marginBottom: pt(0) },
    ] },
  headingStyles: [{ id: 'lead-in', marginTop: pt(0) }], // under the opener, level with column 2
  unorderedLists: { color: col('brand'), fontWeight: 400, gap: mm(2.4),
    marginTop: pt(0), marginBottom: pt(0), itemSpacing: pt(2) },
  paragraphStyles: [{ id: 'colophon', fontSize: pt(7.5), lineHeight: pt(10), color: col('muted') }],
  chipStyles: [ // the first style is the default: pin names in mono on the violet wash
    { id: 'pin', fontFamily: MONO, fontSize: em(0.88), color: col('brand'),
      background: col('tint'), borderWidth: pt(0), borderRadius: pt(1.2) },
    { id: 'code', fontFamily: MONO, fontSize: em(0.9), color: col('ink'), // bare: a face change
      backgroundEnabled: false, borderWidth: pt(0), paddingX: pt(0) },
    ...[['preview', 'hazard', 'ink'], ['planned', 'zebra', 'muted'], ['active', 'brand', 'paper']]
      .map(([id, fill, ink]) => ({ id, fontFamily: COND, bold: true, color: col(ink),
        background: col(fill), borderWidth: pt(0), borderRadius: pt(1.2) })),
  ],
  calloutStyles: [{ id: 'ratings', title: 'Absolute maximum ratings', backgroundEnabled: false,
    stripe: { enabled: true, side: 'top', width: pt(2.5), color: col('hazard') }, // no fill
    padding: { top: mm(2.2), right: mm(0), bottom: mm(0), left: mm(0) }, marginTop: pt(2),
    titleStyle: { fontSize: pt(9), ...caps(9, 700), color: col('ink') },
    body: { fontSize: pt(8.5), lineHeight: pt(12) },
    lists: { bulletChar: '–', color: col('muted') } }],
  // #region styles: a house table style, then one named variant per table, stating what differs
  tableStyle: { headerBackground: col('brand'), headerColor: col('paper'), headerFontFamily: COND,
    headerFontSize: pt(8.5), bodyFontSize: pt(8), rules: 'horizontal', borderColor: col('rule'),
    borderWidth: pt(0.5), cellPadding: mm(1.3) },
  tableStyles: [ // a resource picks one with table.styleId
    // White rules cut the fills apart and show where each merge and each group ends.
    { id: 'electrical', borderColor: col('paper'), borderWidth: pt(1.4), cellPadding: mm(1.1) },
    // Written out although it is the default: 'clip' and 'hide' cut a table taller than the page.
    { id: 'grouped', overflow: 'split', continuedSuffix: '(continued)',
      continuesMarker: 'Continued on the next page' },
    // A compact list in the condensed face, boxed by a rounded outer frame.
    { id: 'ordering', headerBackground: col('tint'), headerColor: col('brand'),
      rules: 'outer', borderRadius: mm(1.5), bodyFontFamily: COND },
  ],
  captionStyle: { fontFamily: COND, fontSize: pt(9.5), labelColor: col('brand'), gap: mm(2),
    note: { fontSize: pt(7.5), color: col('muted') } },
  // #endregion
  header, footer,
});

// ─── 2 · Content ────────────────────────────────────────────────────────────
const markdown = String.raw`---
title: "PX-7021 digital temperature sensor"
subtitle: "DS-7021 · Rev. 0.3"
author: "Pyxis Microdevices"
publishDate: "September 2026"
---

# PX-7021 {kicker="Digital temperature sensor" lead="±0.1 °C accuracy from 1.4 µA, with an I²C and SMBus interface, in a 2 × 2 mm package" k1="±0.1 °C" k1l="Accuracy, −20 °C to 50 °C" k2="1.4 µA" k2l="At one reading a second" k3="2 × 2 mm" k3l="8-pin DFN package"}

## Features {style="lead-in"}

- ±0.1 °C maximum error from −20 °C to 50 °C
- ±0.3 °C maximum error from −40 °C to 125 °C
- 16-bit result, with a resolution of 0.0078 °C
- 1.4 µA at one reading a second, 0.1 µA in shutdown
- Supply from 1.6 V to 5.5 V, 5.5 V-tolerant interface
- I²C and SMBus, from 1 kHz to 1 MHz, with bus timeout
- Eight bus addresses, selected by three pins
- Alert output, in comparator or interrupt mode
- 8-pin DFN, 2 × 2 mm, with an exposed pad (:ref{id="pinout" style="full"})

## Applications

- Cold-chain loggers for vaccines and fresh food
- Wearable and home thermometry
- Battery packs, chargers and power banks
- Thermostats and building controls
- Thermal protection for processors and power stages
- Laboratory and medical instruments

:::columnbreak

## Description

The PX-7021 is a digital temperature sensor for coin-cell designs that must read within a tenth of a degree. A 16-bit converter reads an on-chip bandgap sensor, and every part is trimmed at two temperatures on the production line, so the board needs no calibration and the host no look-up table: one step of the result is 1/128 °C.

Between conversions the sensor sleeps: at one reading a second it draws 1.4 µA on average. Two limit registers drive the open-drain :chip[ALERT] output, which can wake a sleeping host when the temperature leaves a window.

:ref{id="circuit" style="full"} shows the typical circuit, with one decoupling capacitor and the bus pull-ups. With its address pins tied to ground the sensor answers at 48h.

:chip[Preview]{style="preview"} Engineering samples of the DFN versions are available now. The limits in :ref{id="electrical" style="full"} are preliminary and may change before production release.

:::pagebreak

## Specifications

:::callout{type="ratings"}
- Supply voltage, *V*~DD~ to GND: **−0.3 V to 6 V**
- SDA, SCL and ALERT to GND: **−0.3 V to 6 V**
- A0 to A2 to GND: **−0.3 V to *V*~DD~ + 0.3 V**
- Current into any pin: **±10 mA**
- Storage temperature: **−60 °C to 150 °C**
- Electrostatic discharge, human-body model: **±2 kV**
:::

Stress beyond these ratings can damage the device for good. Design to the operating conditions below.

### Recommended operating conditions

Operate the sensor from 1.6 V to 5.5 V, at ambient temperatures from −40 °C to 125 °C, with less than 50 mV of ripple on the supply. The bus pull-ups may return to any supply up to 5.5 V, so a sensor run from 1.8 V can share a bus with 5 V parts without a level shifter.

### Electrical characteristics

:ref{id="electrical" style="full"} lists the limits over the full supply and temperature range. Typical values are the mean of the characterization lots at 3.3 V and 25 °C; they are not guaranteed. Accuracy is tested on every part at 25 °C and 50 °C; values marked ² come from characterization only.

## Pin configuration and functions

:ref{id="pinout" style="full"} shows the package from above. A dot on the top face marks pin 1, and the pins count counterclockwise from it. The exposed pad under the package is the sensor's thermal path to the board: solder it to a ground pour. :ref{id="pins" style="full"} describes each pin.

## Detailed description

A host talks to the PX-7021 through eleven registers, listed with their reset values in :ref{id="registers" style="full"}. Two-byte registers are read and written most significant byte first.

### Temperature conversion

A conversion takes 10.5 ms at 16 bits and 3.1 ms at 12 bits. In continuous mode the sensor starts a new conversion at the programmed rate, from one every four seconds to eight a second, and sleeps in between; in one-shot mode it converts once, stores the result and shuts down again. The result register always holds the last complete reading, so a read never catches a conversion halfway.

The result is a signed 16-bit value in steps of 1/128 °C. Values above 7FFFh are negative: 1900h reads as 50 °C, and E700h as −50 °C.

### Serial interface

The sensor is a target on an I²C or SMBus bus, at clock rates up to 1 MHz. Tie each of A0, A1 and A2 to ground or to the supply to choose one of eight addresses, from 48h to 4Fh. In SMBus mode a clock held low for more than 30 ms resets the interface, so a host that crashes in mid-transfer cannot lock the bus. The sensor also answers the I²C general-call reset command.

### Alert output

The :chip[ALERT] pin compares every result with the limits in THIGH and TLOW. In comparator mode it stays asserted while the temperature is above THIGH and releases once it falls below TLOW, which gives a thermostat its hysteresis. In interrupt mode it asserts once per crossing, and releases when the host reads STATUS, or when the sensor answers a read of the SMBus alert response address.

## Packaging and ordering

:ref{id="outline" style="full"} draws the package and its land pattern: the DFN-8 body is 2 mm square and 0.55 mm high, with a 0.5 mm pin pitch and a 0.8 × 1.5 mm exposed pad. :ref{id="ordering" style="full"} lists the versions and their order codes. The top of each part carries its number over a date code, YWWL: the year, the work week and the lot.

Parts are rated at moisture sensitivity level 1, so they need no dry storage, and survive three reflow cycles at a peak of 260 °C. Reflow shifts the reading by less than 0.02 °C.

## Layout guidelines

The sensor measures the copper under its exposed pad. For air temperature, place it at the edge of the board, away from regulators and processors, and cut slots in the board around it so that heat from the rest of the circuit reaches it slowly. For the temperature of a surface, do the opposite: a solid pour and a row of vias carry heat from the surface to the pad. Keep the decoupling capacitor on the same side of the board as the sensor and close to its supply pin: 2 mm at most.

## Revision history

**Rev. 0.3**, September 2026: preliminary release, with limits from the first characterization lots. Adds the WLCSP-4 version and the SMBus timeout.

**Rev. 0.2**, May 2026: advance information for early customers, with typical values only.

**Rev. 0.1**, February 2026: product brief, with the target accuracy and supply current.

:::paragraphs{style="colophon"}
A work of fiction: Pyxis Microdevices and the PX-7021 are imaginary, and so are these figures; do not design with them. Set in Fira Sans, Fira Sans Condensed and Fira Mono (SIL Open Font License) · Text and drawings: original, licensed CC BY 4.0.
:::
`; // content.<lang>.md, inlined by the Cookbook
const electrical = String.raw`Parameter		Symbol	Conditions	Value			Unit
				Min	Typ	Max	
Temperature sensor	Accuracy^1^	*T*~ACC~	−20 °C to 50 °C	−0.1	±0.05	0.1	°C
			−40 °C to 125 °C	−0.3	±0.1	0.3	°C
	Resolution		16-bit result		0.0078		°C
	Repeatability^2^		1 Hz, 100 readings		±0.008		°C
	Long-term drift^2^		500 h at 125 °C		0.02		°C
Power supply	Supply voltage	*V*~DD~		1.6	3.3	5.5	V
	Average supply current^3^	*I*~DD~	1 conversion per second		1.4	2.5	µA
	Supply current, converting	*I*~CONV~			120	175	µA
	Shutdown current	*I*~SD~	bus idle		0.1	0.5	µA
	Power-on reset threshold	*V*~POR~	*V*~DD~ rising		1.2	1.45	V
Conversion	Conversion time	*t*~CONV~	16-bit result		10.5	12	ms
			12-bit result		3.1	3.6	ms
	Conversion rate	*f*~CONV~	continuous mode	0.25		8	Hz
Digital inputs and outputs	High-level input voltage	*V*~IH~		0.7 *V*~DD~			V
	Low-level input voltage	*V*~IL~				0.3 *V*~DD~	V
	Low-level output voltage	*V*~OL~	3 mA sink			0.4	V
	Input leakage current	*I*~IN~		−1		1	µA
	Pin capacitance	*C*~IN~			3		pF
Serial interface	Clock frequency	*f*~SCL~	Fast-mode Plus	1		1000	kHz
	Bus timeout	*t*~TIMEOUT~	SMBus mode	25	30	35	ms
`; // the tables: TSV, pasted from a spreadsheet
const pins = String.raw`Pin	Name	Type	Description
**Power**			
8	:chip[VDD]	P	Supply, 1.6 V to 5.5 V. Decouple with 100 nF within 2 mm of the pin.
4	:chip[GND]	G	Ground.
EP	:chip[EP]	G	Exposed pad, the thermal path to the board. Solder it to ground.
**Serial interface**			
1	:chip[SDA]	I/O	Serial data, open drain, 5.5 V-tolerant.
2	:chip[SCL]	I	Serial clock, Schmitt-trigger input.
3	:chip[ALERT]	O	Alert output, open drain. Leave it open when unused.
**Address select**			
5	:chip[A0]	I	Address bit 0. Tie to GND or *V*~DD~, never leave it floating.
6	:chip[A1]	I	Address bit 1. Tie to GND or *V*~DD~.
7	:chip[A2]	I	Address bit 2. Tie to GND or *V*~DD~.
`;
const registers = String.raw`Addr.	Register	Reset	Contents
**Measurement**			
00h	:chip[TEMP]	8000h	The last complete result, read only.\n• 8000h until the first result\n• Signed, in steps of 1/128 °C\n• At 12 bits, bits 3 to 0 read zero\n• Two bytes, most significant first
04h	:chip[STATUS]	00h	Flags, read only. Reading STATUS releases ALERT in interrupt mode.\n• Bit 7, BUSY: still converting\n• Bit 6, HIGH: a result crossed THIGH\n• Bit 5, LOW: a result crossed TLOW\n• Bit 4, TRIM: the trim check failed at power-on
**Configuration**			
01h	:chip[CONFIG]	0000h	Operating mode and alert behavior.\n• Bits 15 and 14, MODE: continuous, one-shot or shutdown\n• Bit 13, RES: a 12-bit result instead of 16 bits\n• Bit 12, AVG: each result averages eight readings\n• Bits 11 and 10, FAULTS: 1, 2, 4 or 6 results beyond a limit before ALERT asserts\n• Bit 9, POL: ALERT active high\n• Bit 8, INT: interrupt mode instead of comparator mode
05h	:chip[RATE]	02h	Conversion rate in continuous mode.\n• 00h to 05h: 0.25, 0.5, 1, 2, 4 or 8 conversions a second\n• Higher values read back as 05h
06h	:chip[ONESHOT]	00h	Any write starts one conversion.\n• Shuts down again afterwards\n• Ignored in continuous mode
07h	:chip[OFFSET]	0000h	Added to every result, in the format of TEMP.\n• From −8 °C to 8 °C\n• Cleared by a power-on reset
**Limits**			
02h	:chip[TLOW]	F600h	Low limit, in the format of TEMP.\n• −20 °C after reset\n• Keep it below THIGH
03h	:chip[THIGH]	3C00h	High limit, in the format of TEMP.\n• 120 °C after reset\n• In comparator mode, ALERT releases below TLOW
**Identification**			
0Eh	:chip[SERIAL]	—	A 48-bit number unique to each part, read only.\n• Read six bytes, from 0Eh
FEh	:chip[MAKER]	5058h	Manufacturer, read only: PX in ASCII.
FFh	:chip[DEVICE]	7021h	Device, read only.\n• Bits 15 to 4: the part number, 702h\n• Bits 3 to 0: the silicon revision
`;
const ordering = String.raw`Order code	Package	Packing	Status
**PX-7021-DFN-R**	DFN-8, 2 × 2 mm	Reel of 3000	:chip[Preview]{style="preview"}
**PX-7021-DFN-T**	DFN-8, 2 × 2 mm	Cut tape, 250	:chip[Preview]{style="preview"}
**PX-7021-CSP-R**	WLCSP-4, 0.8 × 0.8 mm	Reel of 5000	:chip[Planned]{style="planned"}
**PX-7021-EVM**	Evaluation board	Box of 1	:chip[Available]{style="active"}
`;

// #region art: the logo, pinout and circuit at column width, the outline at page width, in mm
const SCALE = 10; // px per mm of the drawings' intrinsic size: the engine keeps only the ratio
// The outline is 48.3 mm tall so that the text above it ends on a whole grid line: a closing
// page lifts its page-wide floats to the text (layout.hugClosingFloats), and here none is left.
const LOGO = [24, 24], PINOUT = [87, 47], CIRCUIT = [87, 56], OUTLINE = [180, 48.3]; // mm
// One size family, in mm at 1:1 (1 mm = 2.83 pt): names 7.4 pt, labels and dimensions 6.8 pt,
// notes 6.2 pt, pin numbers 6 pt; all under the 9.3 pt text and the 9.5 pt captions.
const TEXT = { name: 2.6, label: 2.4, note: 2.2, pin: 2.1 };
const svg = ([w, h], body) => `<svg xmlns="http://www.w3.org/2000/svg" width="${w * SCALE}" `
  + `height="${h * SCALE}" viewBox="0 0 ${w} ${h}">${body}</svg>`;
const label = (x, y, s, { anchor = 'start', color = 'ink', size = TEXT.label } = {}) =>
  `<text x="${x}" y="${y}" font-size="${size}" font-family="${MONO}" text-anchor="${anchor}" `
  + `fill="${palette[color]}">${s}</text>`; // Fira Mono 400, the label face
const logo = svg(LOGO, `<circle cx="12" cy="12" r="12" fill="${palette.brand}"/><path fill="`
  + `${palette.paper}" d="M12 3 14 10 21 12 14 14 12 21 10 14 3 12 10 10Z"/>`); // a compass star
function pinout() { // the DFN-8 from above: pins 1 to 4 down the left, 5 to 8 back up the right
  const [cx, cy] = [PINOUT[0] / 2, PINOUT[1] / 2];
  const [bw, bh, pitch] = [36, 46, 9.4]; // body and pin pitch: a diagram, not to scale
  const [left, right] = [cx - bw / 2, cx + bw / 2];
  const pins = ['SDA', 'SCL', 'ALERT', 'GND', 'A0', 'A1', 'A2', 'VDD'].map((name, i) => {
    const onLeft = i < 4;
    const y = cy + ((onLeft ? i : 7 - i) - 1.5) * pitch;
    return `<rect x="${(onLeft ? left : right) - 2.4}" y="${y - 1.5}" width="4.8" height="3" `
      + `rx="0.5" fill="${palette.brand}"/>${onLeft
        ? label(left - 4.2, y + 0.95, `${name} ${i + 1}`, { anchor: 'end', size: TEXT.name })
        : label(right + 4.2, y + 0.95, `${i + 1} ${name}`, { size: TEXT.name })}`;
  });
  // The exposed pad is under the package: from above, a hidden outline, dashed.
  return svg(PINOUT, `<rect x="${left}" y="${cy - bh / 2}" width="${bw}" height="${bh}" rx="1.6" `
    + `fill="${palette.paper}" stroke="${palette.ink}" stroke-width="0.45"/><rect x="${cx - 9}" `
    + `y="${cy - 12.5}" width="18" height="25" rx="0.6" fill="none" stroke="${palette.brand}" `
    + `stroke-width="0.35" stroke-dasharray="1.4 0.9"/><circle cx="${left + 4}" `
    + `cy="${cy - bh / 2 + 4}" r="1.3" fill="${palette.ink}"/>${pins.join('')}`
    + label(cx, cy + 0.95, 'EP', { anchor: 'middle', color: 'brand', size: TEXT.name }));
}
function circuit() { // the typical application: one capacitor, three pull-ups, address 48h
  const wire = (d, w = 0.3) => `<path d="${d}" fill="none" stroke="${palette.ink}" `
    + `stroke-width="${w}"/>`;
  const dots = (...xy) => xy.map(([x, y]) => `<circle cx="${x}" cy="${y}" r="0.6" `
    + `fill="${palette.ink}"/>`).join('');
  const box = (x, y, w, h, fill) => `<rect x="${x}" y="${y}" width="${w}" height="${h}" rx="0.8" `
    + `fill="${palette[fill]}" stroke="${palette.ink}" stroke-width="0.35"/>`;
  const small = { size: TEXT.note }, pin = { size: TEXT.pin, color: 'muted', anchor: 'middle' };
  const pullUps = [[59, 23], [63, 28], [67, 33]].map(([x, y]) => wire(`M${x} 6V10M${x} 15.5V${y}`)
    + `<rect x="${x - 0.8}" y="10" width="1.6" height="5.5" fill="${palette.paper}" `
    + `stroke="${palette.ink}" stroke-width="0.3"/>${dots([x, 6], [x, y])}`);
  const lines = [['SDA', 'SDA', 23, 1], ['SCL', 'SCL', 28, 2], ['ALERT', 'INT', 33, 3]]
    .map(([from, to, y, n]) => wire(`M55 ${y}H71`) + label(53.6, y + 0.8, from,
      { ...small, anchor: 'end' }) + label(72.4, y + 0.8, to, small) + label(57, y - 0.7, n, pin));
  const address = ['A0', 'A1', 'A2'].map((name, i) => wire(`M29 ${24 + 5 * i}H25`)
    + label(30.4, 24.8 + 5 * i, name, small) + label(27, 23.3 + 5 * i, 5 + i, pin));
  const g = CIRCUIT[1] - 5; // the ground rail
  return svg(CIRCUIT, wire(`M6 6H78.5V17M6 ${g}H78.5V41M12 6V27.6M12 29.6V${g}M42 6V16M42 44V${g}`
    + `M25 24V${g}`) + wire('M9.4 27.6H14.6M9.4 29.6H14.6', 0.55)
    + dots([12, 6], [12, g], [42, 6], [42, g], [25, 29], [25, 34], [25, g])
    + box(29, 16, 26, 28, 'tint') + box(71, 17, 15, 24, 'paper') + pullUps.join('')
    + lines.join('') + address.join('')
    + label(6, 4.2, 'VDD, 1.6 V to 5.5 V') + label(6, g + 3.6, 'GND')
    + label(8.4, 29.4, '100 nF', { ...small, color: 'muted', anchor: 'end' }) // left of the cap
    + label(68.8, 13.6, '4.7k', { ...small, color: 'muted' })
    + label(29, 14.3, 'PX-7021', { size: TEXT.name, color: 'brand' })
    + label(42, 19.8, 'VDD', { ...small, anchor: 'middle' }) + label(43.2, 14.4, 8, pin)
    + label(42, 42.2, 'GND', { ...small, anchor: 'middle' }) + label(43.2, 48.4, 4, pin)
    + label(27, g - 2.6, 'address 48h', { size: TEXT.pin, color: 'muted' })
    + label(78.5, 38.6, 'MCU', { size: TEXT.name, color: 'brand', anchor: 'middle' }));
}
function outline() { // the DFN-8 at 15:1, four views in a row: top, bottom, side, land pattern
  const ink = (d, w = 0.15) => `<path d="${d}" fill="none" stroke="${palette.ink}" `
    + `stroke-width="${w}"/>`;
  const fill = (d, color) => `<path d="${d}" fill="${palette[color]}"/>`;
  const rect = (x, y, w, h, color, extra = '') => `<rect x="${x}" y="${y}" width="${w}" `
    + `height="${h}" fill="${palette[color]}"${extra}/>`;
  const body = (x, y, w, h) => rect(x, y, w, h, 'paper',
    ` rx="0.6" stroke="${palette.ink}" stroke-width="0.35"`);
  const dim = { anchor: 'middle' };
  const caption = { size: TEXT.note, color: 'muted', anchor: 'middle' };
  const hDim = (x1, x2, y, s) => ink(`M${x1} ${y}H${x2}`) + fill(`M${x1} ${y}l1.3 -0.45v0.9z`
    + `M${x2} ${y}l-1.3 -0.45v0.9z`, 'ink') + label((x1 + x2) / 2, y - 0.9, s, dim);
  const vDim = (x, y1, y2) => ink(`M${x} ${y1}V${y2}`) + fill(`M${x} ${y1}l-0.45 1.3h0.9z`
    + `M${x} ${y2}l-0.45 -1.3h0.9z`, 'ink');
  const cy = 23, rows = [-11.25, -3.75, 3.75, 11.25].map((d) => cy + d); // 0.5 mm pitch
  const pads = (xs, w) => rows.map((y) => xs.map((x) => rect(x, y - 1.875, w, 3.75, 'brand'))
    .join('')).join('');
  const [t, b, s, l] = [4, 50, 94, 140]; // the left edge of each view
  const top = body(t, 8, 30, 30) + `<circle cx="${t + 3.6}" cy="11.6" r="1" fill="${palette.ink}"/>`
    + label(t + 15, 24, '7021', { size: 3.2, anchor: 'middle' }) // the marking, not a label
    + label(t + 15, 29, 'YWWL', { ...caption, size: TEXT.label })
    + ink(`M${t} 7.2V3.2M${t + 30} 7.2V3.2`)
    + hDim(t, t + 30, 4, '2.00') + label(t + 15, 45, 'TOP · MARKING', caption);
  const bottom = body(b, 8, 30, 30) + pads([b, b + 25.5], 4.5) + rect(b + 9, 11.75, 12, 22.5,
    'tint', ` rx="0.4" stroke="${palette.brand}" stroke-width="0.3"`) + label(b + 15, 24, 'EP', dim)
    + ink(`M${b - 0.6} 11.75H${b - 3.7}M${b - 0.6} 19.25H${b - 3.7}`) + vDim(b - 2.8, 11.75, 19.25)
    + label(b - 4.2, 16.4, '0.50', { ...dim, anchor: 'end' }) + label(b + 31.6, 13, 1, caption)
    + label(b + 15, 45, 'BOTTOM · EP 0.80 × 1.50', caption);
  const side = body(s, cy - 4, 30, 8.25) + rect(s, cy + 3.7, 4.5, 0.55, 'brand')
    + rect(s + 25.5, cy + 3.7, 4.5, 0.55, 'brand')
    + ink(`M${s + 30.6} ${cy - 4}H${s + 34.3}M${s + 30.6} ${cy + 4.25}H${s + 34.3}`)
    + vDim(s + 33.5, cy - 4, cy + 4.25)
    + label(s + 35.2, cy + 1, '0.55', { ...dim, anchor: 'start' })
    + label(s + 15, 45, 'SIDE', caption);
  const land = rect(l + 4.5, 8, 30, 30, 'paper', ` fill-opacity="0" stroke="${palette.muted}" `
    + 'stroke-width="0.2" stroke-dasharray="1 0.8"') + pads([l, l + 28.5], 10.5)
    + rect(l + 13.5, cy - 11.25, 12, 22.5, 'brand') + [cy - 5.5, cy + 5.5].map((y) =>
      `<circle cx="${l + 19.5}" cy="${y}" r="2.25" fill="${palette.paper}"/>`).join('') // vias
    + ink(`M${l} 9.3V3.2M${l + 39} 9.3V3.2`) + hDim(l, l + 39, 4, '2.60')
    + label(l + 19.5, 45, 'LAND PATTERN · 0.25 × 0.70', caption);
  return svg(OUTLINE, top + bottom + side + land);
}
// #endregion

// #region resources: each drawing and table is a resource; the floats go where they are cited
const svgResource = (id, caption, altText, [w, h], placement) => ({ id, typeId: 'figure',
  kind: 'svg', caption, altText, placement, createdAt: 0, updatedAt: 0,
  svg: { fileId: `${id}.svg`, width: w * SCALE, height: h * SCALE } }); // fitted to its slot
const table = (id, caption, model, { styleId, placement, note } = {}) => ({ id, typeId: 'table',
  kind: 'table', caption, note, placement, table: { model, styleId }, createdAt: 0, updatedAt: 0 });
// A float takes the first free slot after its first :ref; the logo is never cited, only drawn.
const resources = [
  svgResource('logo', '', 'Pyxis Microdevices', LOGO),
  svgResource('pinout', 'Pin configuration, 8-pin DFN, top view.', 'The package from above: '
    + 'pins 1 to 4 down the left side, 5 to 8 up the right.', PINOUT),
  svgResource('circuit', 'Typical application, bus address 48h.', 'The sensor with a 100 nF '
    + 'capacitor, address pins to ground, and SDA, SCL and ALERT pulled up to a host.', CIRCUIT),
  svgResource('outline', 'Package outline and land pattern, 8-pin DFN, in mm.', 'Top, bottom '
    + 'and side views of the 2 × 2 mm body, and the land pattern with its two vias.', OUTLINE,
  { position: 'bottom', span: 'page' }), // a strip across the foot of a page
  table('electrical', 'Electrical characteristics, *V*~DD~ = 1.6 V to 5.5 V and *T*~A~ = −40 °C '
    + 'to 125 °C unless noted', electricalTable(electrical), { styleId: 'electrical',
    placement: { position: 'top', span: 'page' }, note: 'Typical values at 3.3 V and 25 °C. '
      + '^1^ Tested at 25 °C and 50 °C, the rest by characterization. ^2^ Characterized, not '
      + 'tested in production. ^3^ One conversion a second, bus idle.' }),
  // No placement: these float to the first free slot after their reference and split there.
  table('pins', 'Pin functions', groupedTable(pins, [9, 16, 10, 52]), { styleId: 'grouped',
    note: 'Types: P power, G ground, I input, O open-drain output, I/O open-drain input and '
      + 'output.' }),
  table('registers', 'Register map', groupedTable(registers, [9, 17, 11, 50]), {
    styleId: 'grouped', note: 'Reset values apply at power-on and after a general-call reset.' }),
  table('ordering', 'Order codes', Object.assign(parseTSV(ordering, { headerRows: 1 }), {
    columnWidths: [23, 29, 18, 17] }), { styleId: 'ordering',
    note: 'WLCSP-4: fixed address 48h, no ALERT output.' }),
];
// #endregion

// ─── 3 · Fonts ──────────────────────────────────────────────────────────────
const FONTS = { // every face the layout uses, loaded before the build
  'Fira Sans': ['400', '400i', '600', '600i'], // text; 600 is the bold
  'Fira Sans Condensed': ['400', '400i', '600', '700'], // display: title, heads, captions
  'Fira Mono': ['400'], // labels: pin names, codes, document number, the drawings' labels
};

// ─── 4 · Build & show ───────────────────────────────────────────────────────
const allText = [markdown, electrical, pins, registers, ordering].join('\n'); // all it prints
await prepareFonts(allText, config(), kitFonts(FONTS));
// #region drawing: the drawings' labels stay text, in the document's own label face
// label() writes each <text> with font-family="Fira Mono". loadSvg runs the markup through
// inlineSvgFonts, which embeds that face in the SVG, so the canvas draws the labels in it;
// the PDF sets them as real text in the Fira Mono it embeds.
await loadSvg('logo.svg', logo);
const drawings = { pinout: pinout(), circuit: circuit(), outline: outline() }; // by resource id
for (const [id, markup] of Object.entries(drawings)) await loadSvg(`${id}.svg`, markup);
// #endregion
const doc = await buildDocumentWithFonts({ markdown, resources }, config(),
  { ...kitFonts(FONTS), text: allText });
showPages(doc, { title: 'PX-7021 datasheet' });
offerPdf(() => renderToPdf(doc, { fontProvider: fontsourceProvider, resourceBytes: imageBytes }),
  `${RECIPE}.pdf`); // the same faces; the drawings stay vectors with real text

// ─── Kit ── helpers shared by every Cookbook recipe · postext.dev/cookbook ─────

// ─── Kit · core v1 ── the same in every recipe · postext.dev/cookbook
function mm(value) { return { value, unit: 'mm' }; }
function pt(value) { return { value, unit: 'pt' }; }
function em(value) { return { value, unit: 'em' }; }
/** The sample language's string: t({ en: 'Figure', es: 'Figura' }). */
function t(strings) { return strings[LANG] ?? Object.values(strings)[0]; }
/** A file in this recipe's assets folder, served from the Postext repo by jsDelivr. */
function asset(file) { return `https://cdn.jsdelivr.net/gh/drnachio/postext@main/cookbook/${RECIPE}/assets/${file}`; }

// ─── Kit · fonts v3 ── the same in every recipe · postext.dev/cookbook
// Postext loads the faces a config asks for before layout (prepareFonts,
// buildDocumentWithFonts) and asks the kit for the files: Fontsource's, the
// files the PDF embeds too.

/** The options of buildDocumentWithFonts / prepareFonts / withLoadedFonts:
 *  the Fontsource resolver, and the faces of FONTS loaded with the ones the
 *  config names. FONTS = { 'Family Name': ['400', '400i', '700'] }. */
function kitFonts(FONTS = {}) {
  const faces = Object.entries(FONTS).flatMap(([family, specs]) => specs.map((spec) =>
    ({ family, weight: parseInt(spec, 10), style: spec.endsWith('i') ? 'italic' : 'normal' })));
  return { resolve: fontsourceResolver, faces };
}

/** A face's Fontsource files, in a fixed order: latin, then latin-ext and greek
 *  when `text` needs them and the family ships them (kitSubsetsFor), each with
 *  its unicode-range. Null for a weight or slant Fontsource does not ship. */
async function fontsourceResolver(family, weight, style, { text = '' } = {}) {
  const id = fontsourceId(family);
  const meta = await fontsourceMeta(family);
  if (meta && !(meta.weights.includes(weight) && meta.styles.includes(style))) return null;
  kitStatus('Loading fonts…');
  const at = await fontsourceAt(id);
  return ['latin', ...kitSubsetsFor(text, meta)].map((subset) => ({
    source: `${at}files/${id}-${subset}-${weight}-${style}.woff2`,
    unicodeRange: kitRanges()[subset],
  }));
}

/** The unicode-range of each Fontsource file the kit loads (a function: the
 *  kit is inlined after the pen's code, which runs before a const would be set). */
function kitRanges() {
  return {
    latin: 'U+0000-00FF,U+0131,U+0152-0153,U+02BB-02BC,U+02C6,U+02DA,U+02DC,U+0304,U+0308,U+0329,'
      + 'U+2000-206F,U+20AC,U+2122,U+2191,U+2193,U+2212,U+2215,U+FEFF,U+FFFD',
    'latin-ext': 'U+0100-02BA,U+02BD-02C5,U+02C7-02CC,U+02CE-02D7,U+02DD-02FF,U+0304,U+0308,U+0329,'
      + 'U+1D00-1DBF,U+1E00-1E9F,U+1EF2-1EFF,U+2020,U+20A0-20AB,U+20AD-20C0,U+2113,U+2C60-2C7F,U+A720-A7FF',
    greek: 'U+0370-03FF',
  };
}

/** For the cjk, arabic and comics blocks, which add their own files: the
 *  faces of `faces` = { 'Family Name': ['400', '400i', '700'] }. `text` is the sample:
 *  č ł † α χ also load latin-ext and greek files (kitSubsetsFor). With
 *  `optional`, a face Fontsource does not ship is skipped instead of failing.
 *  The files are added once all have loaded, in the order asked (latin, then
 *  latin-ext, then greek), whatever order they arrive in: the last one added
 *  wins a character two files hold. Resolves to the number of faces added. */
async function loadFonts(faces, text = '', { optional = false } = {}) {
  kitStatus('Loading fonts…');
  const ranges = kitRanges();
  const jobs = [];
  for (const [family, specs] of Object.entries(faces)) {
    const id = fontsourceId(family);
    const todo = [...new Set(specs)].map((spec) => [parseInt(spec, 10), spec.endsWith('i') ? 'italic' : 'normal'])
      .filter(([weight, style]) => !hasFace(family, weight, style)); // before any await
    const at = fontsourceAt(id);
    const meta = optional || /[^\0-ÿ]/u.test(text) ? await fontsourceMeta(family) : null;
    const subsets = ['latin', ...kitSubsetsFor(text, meta)];
    for (const [weight, style] of todo) {
      if (optional && !(meta?.weights.includes(weight) && meta.styles.includes(style))) continue;
      for (const subset of subsets) {
        const url = `${await at}files/${id}-${subset}-${weight}-${style}.woff2`;
        const face = new FontFace(family, `url(${url}) format('woff2')`,
          { weight: String(weight), style, unicodeRange: ranges[subset] });
        jobs.push(face.load().catch(() => {
          if (subset === 'latin' && !optional) throw new Error(`Fontsource has no ${family} ${weight} ${style}`);
        }));
      }
    }
  }
  const ready = await Promise.all(jobs).catch((error) => { kitFail(error); throw error; });
  return ready.filter((face) => face && document.fonts.add(face)).length;
}

/** A loaded FontFace covers this family, weight and style (fonts.check() would
 *  also say yes for families nobody declared). */
function hasFace(family, weight, style) {
  for (const face of document.fonts) {
    if (face.status !== 'loaded' || face.style !== style) continue;
    if (face.family.replace(/^["']|["']$/g, '') !== family) continue;
    const [low, high = low] = face.weight.split(' ').map(Number);
    if (weight >= low && weight <= high) return true;
  }
  return false;
}

/** The files beyond latin `text` needs that `meta`'s family ships. */
function kitSubsetsFor(text, meta) {
  return [[/[Ā-˿ᴀ-ᶿḀ-ỿ†ℓⱠ-Ɀ꜠-ꟿ]/u, 'latin-ext'], [/[Ͱ-Ͽ]/u, 'greek']]
    .filter(([re, x]) => re.test(text) && meta?.subsets?.includes(x)).map(([, x]) => x);
}

/** Fontsource's id for a family: 'Source Serif 4' → 'source-serif-4'. */
function fontsourceId(family) { return family.toLowerCase().replace(/\s+/g, '-'); }

/** A package's folder at the one version @5 names now (#766). */
function fontsourceAt(id, u = `https://cdn.jsdelivr.net/npm/@fontsource/${id}@`) {
  return (fontsourceAt.c ??= {})[id] ??= fetch(u + '5/package.json').then((r) => r.json())
    .then((p) => p.version || 5, () => 5).then((v) => `${u}${v}/`);
}

/** The family's Fontsource metadata (weights, styles, subsets), or null. */
function fontsourceMeta(family) {
  fontsourceMeta.cache ??= new Map();
  const id = fontsourceId(family);
  if (!fontsourceMeta.cache.has(id)) {
    fontsourceMeta.cache.set(id, fetch(`https://api.fontsource.org/v1/fonts/${id}`)
      .then((res) => (res.ok ? res.json() : null), () => null));
  }
  return fontsourceMeta.cache.get(id);
}

// ─── Kit · viewer v2 ── the same in every recipe · postext.dev/cookbook
/** The pages as spreads on a dark desk, page 1 alone, then verso | recto,
 *  each painted when it scrolls near. Other options go to renderPageToCanvas. */
function showPages(docs, { title, width = 460, ...render } = {}) {
  const root = viewer(title);
  const pages = [docs].flat().flatMap((doc) =>
    doc.pages.map((page) => ({ doc, page, n: (doc.pageIndexOffset ?? 0) + page.index })));
  const spreads = [];
  let verso = null;
  for (const p of pages) {
    if (p.n % 2 === 1) { if (verso) spreads.push([verso, null]); verso = p; }
    else { spreads.push([verso, p]); verso = null; }
  }
  if (verso) spreads.push([verso, null]);
  const density = Math.min(window.devicePixelRatio || 1, 2);
  showPages.painter?.disconnect();
  const painter = new IntersectionObserver((entries) => {
    for (const { isIntersecting, target } of entries) {
      if (!isIntersecting) continue;
      painter.unobserve(target);
      const { doc, page } = target.postext;
      renderPageToCanvas(page, doc, target, { ...render, scale: (width * density) / page.width });
    }
  }, { rootMargin: '800px' });
  showPages.painter = painter;
  root.replaceChildren(...spreads.map((pair) => {
    const spread = document.createElement('div');
    spread.className = 'pt-spread';
    for (const p of pair) {
      const figure = document.createElement('figure');
      if (p) {
        const label = p.page.pageLabel || String(p.n + 1);
        const canvas = document.createElement('canvas');
        canvas.postext = p;
        canvas.style.aspectRatio = `${p.page.width} / ${p.page.height}`;
        canvas.setAttribute('role', 'img');
        canvas.setAttribute('aria-label', `Page ${label}`);
        const folio = document.createElement('figcaption');
        folio.textContent = label;
        figure.append(canvas, folio);
        painter.observe(canvas);
      } else figure.className = 'pt-blank';
      spread.append(figure);
    }
    return spread;
  }));
  kitStatus(`${pages.length} ${pages.length === 1 ? 'page' : 'pages'}`);
  document.documentElement.dataset.postext = 'ready';
  return pages.length;
}

/** The desk, the bar and the error reporting, created once. */
function viewer(title) {
  if (!document.getElementById('pt-kit')) {
    document.head.insertAdjacentHTML('beforeend', `<style id="pt-kit">
      :root { color-scheme: dark; }
      body { margin: 0; background: #0e1014; color: #b9bcc4; font: 13px/1.45 system-ui, sans-serif; }
      #pt-bar { position: sticky; top: 0; z-index: 1; display: flex; flex-wrap: wrap; align-items: center;
        gap: 6px 16px; padding: 10px 16px; background: rgb(14 16 20 / .92); backdrop-filter: blur(6px);
        border-bottom: 1px solid #23262d; }
      #pt-bar strong { color: #f4f1ea; font-weight: 600; }
      #pt-actions { display: flex; gap: 12px; margin-left: auto; }
      #pt-actions a, #pt-actions button { color: #d8a21a; font: inherit; background: none; border: 0; padding: 0; cursor: pointer; }
      #pages { display: grid; justify-items: center; gap: 48px; padding: 32px 16px 72px; }
      .pt-spread { display: flex; }
      .pt-spread figure { margin: 0; width: min(460px, 44vw); }
      .pt-spread canvas { display: block; width: 100%; background: #fff;
        box-shadow: 0 1px 2px rgb(0 0 0 / .5), 0 22px 44px -16px rgb(0 0 0 / .8); }
      .pt-spread figure:first-child canvas { box-shadow: inset -14px 0 14px -14px rgb(0 0 0 / .18), 0 1px 2px rgb(0 0 0 / .5), 0 22px 44px -16px rgb(0 0 0 / .8); }
      .pt-spread figcaption { margin-top: 10px; text-align: center; font: 600 10px/1 system-ui, sans-serif;
        letter-spacing: .18em; text-transform: uppercase; color: #6c7079; }
      .pt-blank { visibility: hidden; }
      @media (max-width: 760px) {
        .pt-spread { flex-direction: column; gap: 32px; }
        .pt-spread figure { width: min(460px, 92vw); }
        .pt-blank { display: none; }
      }
    </style>`);
    document.body.insertAdjacentHTML('afterbegin',
      '<header id="pt-bar"><strong id="pt-title"></strong><span id="pt-status" role="status"></span><span id="pt-actions"></span></header>');
    document.getElementById('pt-title').textContent = document.title || 'Postext';
    addEventListener('error', (event) => kitFail(event.error ?? event.message));
    addEventListener('unhandledrejection', (event) => kitFail(event.reason));
  }
  if (title) document.getElementById('pt-title').textContent = title;
  return document.getElementById('pages')
    ?? document.body.appendChild(Object.assign(document.createElement('main'), { id: 'pages' }));
}

function kitStatus(text) {
  viewer();
  document.getElementById('pt-status').textContent = text;
}

function kitFail(error) {
  document.documentElement.dataset.postext = 'error';
  kitStatus(`Error: ${error?.message ?? error}`);
}

// ─── Kit · pdf v3 ── the same in every recipe that exports a PDF
/** The Fontsource files the screen used, as TrueType, with their range and
 *  place: the nearest weight the family ships, upright with no italic;
 *  latin, then what its letters need (kitSubsetsFor). */
async function fontsourceProvider(family, weight, style, request) {
  const id = fontsourceId(family);
  const meta = await fontsourceMeta(family);
  const weights = meta?.weights?.length ? meta.weights : [400, 700];
  const w = weights.reduce((a, b) => (Math.abs(b - weight) < Math.abs(a - weight) ? b : a));
  const s = style === 'italic' && meta && !meta.styles.includes('italic') ? 'normal' : style;
  const text = String.fromCodePoint(...(request?.codePoints ?? []));
  const files = await Promise.all(['latin', ...kitSubsetsFor(text, meta)].map(async (subset, order) => {
    const res = await fetch(`${await fontsourceAt(id)}files/${id}-${subset}-${w}-${s}.woff2`);
    if (!res.ok) throw new Error(`Fontsource has no ${family} ${w} ${s} ${subset}`);
    return Object.assign(await decompressWoff2(new Uint8Array(await res.arrayBuffer())),
      { unicodeRange: kitRanges()[subset], order });
  }));
  return files.length === 1 ? files[0] : files;
}

/** A "Build the PDF" button; then "Open the PDF" (a new tab: CodePen's frame
 *  shows no PDFs) and a download link. */
function offerPdf(makePdf, filename) {
  viewer();
  const button = Object.assign(document.createElement('button'), { type: 'button', textContent: 'Build the PDF' });
  button.dataset.postextPdf = filename;
  button.addEventListener('click', async () => {
    button.disabled = true;
    button.textContent = 'Building the PDF…';
    try {
      const bytes = await makePdf();
      const url = URL.createObjectURL(new Blob([bytes], { type: 'application/pdf' }));
      const size = `${Math.max(1, Math.round(bytes.length / 1024))} KB`;
      button.replaceWith(
        Object.assign(document.createElement('a'), { href: url, target: '_blank', rel: 'noopener', textContent: 'Open the PDF ↗' }),
        Object.assign(document.createElement('a'), { href: url, download: filename, textContent: `Download ${filename} · ${size}` }));
    } catch (error) {
      button.disabled = false;
      button.textContent = 'Build the PDF';
      kitFail(error);
    }
  });
  document.getElementById('pt-actions').append(button);
}

// ─── Kit · images v3 ── recipes with pictures · postext.dev/cookbook
/** Registers a photo or PNG for the canvas and keeps its bytes for the PDF.
 *  fetch → ImageBitmap never taints the canvas (a plain cross-origin <img> would). */
async function loadImage(fileId, url) {
  const res = await fetch(url);
  if (!res.ok) throw new Error(`Image not found (${res.status}): ${url}`);
  const bytes = new Uint8Array(await res.arrayBuffer());
  registerResourceImage(fileId, await createImageBitmap(new Blob([bytes])));
  (loadImage.bytes ??= new Map()).set(fileId, bytes);
}

/** Registers SVG markup as a vector image, its fonts inside (inlineSvgFonts, ≥ 1.25).
 *  `options` go to registerResourceImage: { singleInk: true } tints it on the canvas. */
async function loadSvg(fileId, svg, options) {
  if (typeof inlineSvgFonts === 'function') svg = await inlineSvgFonts(svg, svgFaces);
  const img = new Image();
  img.src = `data:image/svg+xml;charset=utf-8,${encodeURIComponent(svg)}`;
  await img.decode();
  registerResourceImage(fileId, img, options);
  (loadImage.bytes ??= new Map()).set(fileId, new TextEncoder().encode(svg));
}

/** A face's Fontsource files: nearest weight; latin + what the SVG sets. */
async function svgFaces(family, weight, style, { codePoints = [] } = {}) {
  const [id, m] = [fontsourceId(family), await fontsourceMeta(family)];
  const w = m?.weights.reduce((a, b) => (Math.abs(b - weight) < Math.abs(a - weight) ? b : a)) ?? weight;
  const s = m?.styles.includes(style) === false ? 'normal' : style;
  return Promise.all(['latin', ...kitSubsetsFor(String.fromCodePoint(...codePoints), m)].map(async (x) => new Uint8Array(
    await (await fetch(`${await fontsourceAt(id)}files/${id}-${x}-${w}-${s}.woff2`)).arrayBuffer())));
}

/** renderToPdf({ resourceBytes: imageBytes }) */
function imageBytes(fileId) { return loadImage.bytes?.get(fileId); }

/** renderToHtml({ resourceImageUrl: imageUrl }) */
function imageUrl(fileId) {
  const bytes = imageBytes(fileId);
  if (!bytes) return undefined;
  imageUrl.urls ??= new Map();
  if (!imageUrl.urls.has(fileId)) {
    const type = /\.svg$/i.test(fileId) ? 'image/svg+xml' : /\.png$/i.test(fileId) ? 'image/png' : 'image/jpeg';
    imageUrl.urls.set(fileId, URL.createObjectURL(new Blob([bytes], { type })));
  }
  return imageUrl.urls.get(fileId);
}

// ─── /Kit ───────────────────────────────────────────────────────────────────────
```

## Variantes

### Séparer chaque rang par un filet gris

Des filets d’un demi-point dans le gris `rule` de la palette séparent chaque rang, avec ou sans fond ; les filets blancs disparaissent là où deux rangs sans fond se touchent.

```diff
-    { id: 'electrical', borderColor: col('paper'), borderWidth: pt(1.4), cellPadding: mm(1.1) },
+    { id: 'electrical', borderColor: col('rule'), borderWidth: pt(0.5), cellPadding: mm(1.1) },
```

### Poser les légendes de tableau sur une barre

Le style de légende du type tableau peut peindre une barre derrière la légende, ici à l’encre avec le libellé dans le jaune `hazard`.

```diff
-    ...(type.id === 'table' && { captionStyle: { position: 'above' } }) })),
+    ...(type.id === 'table' && { captionStyle: { position: 'above', backgroundEnabled: true,
+      background: col('ink'), color: col('paper'), labelColor: col('hazard') } }) })),
```

## Erreurs fréquentes

- **Les cellules fusionnées demandent des cellules hiddenBy : utilisez mergeCells.** Les cellules sont placées selon leur position dans le tableau de la ligne : une cellule fusionnée demande donc des cellules de remplacement marquées hiddenBy là où elle s’étend ; les omettre, comme le fait le HTML, décale toutes les colonnes suivantes. Construisez les fusions avec mergeCells. Depuis postext 1.5, un tableau dont la grille est irrégulière est signalé dans doc.contentWarnings comme raggedTableGrid, et parseTSV(text, { headerRows }) marque les lignes d’en-tête.
- **Les fichiers Fontsource couvrent les lettres, pas les symboles.** Le kit intègre le fichier latin Fontsource d’un caractère, plus son fichier latin-ext pour č, ł, † et son fichier greek pour α, χ (dans une famille qui en fournit un : ce n’est pas le cas de Lora et de Gelasio), quand le texte les compose, à l’écran et dans le PDF. Les symboles comme →, ≈, ✓ et ★ ne figurent dans aucun de ces fichiers et manquent dans le PDF : dessinez-les, composez-les en maths, ou choisissez un caractère dont les fichiers les contiennent.

- La première partie d’un tableau coupé laisse le pied de sa colonne au texte quand trois lignes ou plus y tiennent, et le fait toujours dans une colonne qui contient déjà un flottant. Faites commencer un long tableau là où sa colonne ne contient aucun autre flottant, comme la carte de registres, et ajustez ses rangs pour que la première partie atteigne le pied de la colonne.
- Les éléments texte de maquette sont centrés par défaut. Le chapeau a une largeur fixe : il lui faut donc `align: 'left'` pour s’aligner sous la référence du composant.
- Sur la dernière page d’un chapitre, Postext remonte les flottants pleine largeur placés sous le texte jusqu’à une ligne de texte sous lui : une figure `bottom` s’y place donc sous la dernière ligne du texte au lieu du pied de page. La page 4 est rédigée pour remplir ses colonnes, et le dessin du boîtier mesure 48,3 mm de haut pour que le texte au-dessus finisse sur une ligne de grille. Le dessin n’a alors plus de place pour remonter et finit au niveau du pied des autres pages. `layout.hugClosingFloats: false` désactive ce déplacement.

## Crédits

- Recette: Ignacio Ferro ([@drnachio](https://github.com/drnachio))
- Caractères: Fira Sans (OFL-1.1), Fira Sans Condensed (OFL-1.1), Fira Mono (OFL-1.1)
- Code: MIT · Contenu d’exemple: CC-BY-4.0

## Recettes liées

- [Nº 036 · Catalogue de vente par correspondance, images en cellules](https://postext.dev/fr/cookbook/seed-catalogue.md): Un catalogue de graines dont le tarif est un tableau lu depuis un TSV, un sachet peint dans la cellule de chaque variété, la liste coupée sur une double page. · Niveau 3 (Avancé) · Catalogues
- [Nº 050 · Notice de produit avec consignes de sécurité](https://postext.dev/fr/cookbook/product-manual-warnings.md): La notice allemande d’une bouilloire, dont les encadrés WARNUNG et VORSICHT portent le triangle sur un bandeau de couleur de signal, avec légendes allemandes. · Niveau 2 (Intermédiaire) · Manuels, guides et ouvrages de référence
- [Nº 002 · Un article sur deux colonnes à équations numérotées](https://postext.dev/fr/cookbook/journal-article-with-maths.md): Un article de physique sur deux colonnes dont les formules en ligne et les sept équations numérotées, composées par MathJax, restent vectorielles dans le PDF. · Niveau 3 (Avancé) · Articles et publications universitaires